R60ABD1 Sleep & Breathing Radar + ESP32-S3-WROOM-1: Parse SIP-S Frames and Publish to MQTT

The R60ABD1 is a 60 GHz sleep and breathing radar module. It reports presence, breathing rate, sleep state and sleep quality over a 3.3 V TTL UART using the SIP-S V1.0 protocol — and it has no Wi-Fi and no MQTT stack. To get that data into a broker or a dashboard, you add a small gateway MCU.

This guide wires the R60ABD1 to the ESP32-S3-WROOM-1 development board (the native-USB board we sell) and shows how to parse the frames and, optionally, publish them to any MQTT broker. It is the bridge half of the two-architecture story in MQTT vs UART: the module does not speak MQTT, the ESP32 does.

What you need

• R60ABD1 module (60 GHz sleep/breathing radar, SIP-S V1.0 over UART)
• ESP32-S3-WROOM-1 dev board — the one used here (DevKitC-1 compatible, 44 pins, native USB)
• Jumper wires
• 5 V from the board's 5V pin (or a separate 5 V supply); shared GND
• Optional: an MQTT broker (Mosquitto, etc.) for the publish step

Power (from the R60ABD1 manual)

The R60ABD1 hardware-design section (user manual v3.6, §3) states:

• Rated supply voltage 4.5–5.5 V (typ 5 V)
• Required input current ≥ 200 mA in normal operation
• Supply ripple ≤ 100 mV

The board's 5V pin can power it; if the radar's peak draw would exceed the board's 5 V budget, use a separate 5 V supply but keep GND common with the ESP32.

ESP32-S3-WROOM-1 GPIO allocation

This board uses native USB (GPIO19/GPIO20) for Serial/JTAG and flashing — there is no external USB-to-serial bridge on GPIO43/44. Pinout is DevKitC-1 compatible, all 44 module pins broken out at 2.54 mm.

Radar ↔ ESP32 wiring (locked):

Both UART lines are 3.3 V TTL, so no level shifter is needed.

Pins to avoid (so you do not lose the debugger or hit strapping):
| GPIO | Why avoid |
|---|---|
| 19, 20 | native USB D+/D- (flash, log, JTAG) |
| 0 | strapping — boot mode |
| 3 | strapping — boot-log enable |
| 26–32 | flash / PSRAM (internal) |
| 45, 46 | internal flash-voltage strapping, not broken out |
| 43, 44 | UART0 — free at hardware level, but ESP-IDF's default console; leave it for logs |

We use UART1 on GPIO17/18: it is clear of every reserved function, and it leaves the native USB and the default console untouched.

Wiring diagram

R60ABD1                 ESP32-S3-WROOM-1
 5V   ───────────────▶  5V
 GND  ───────────────▶  GND
 TX   ───────────────▶  GPIO18   (UART1 RX)
 RX   ───────────────▶  GPIO17   (UART1 TX)

Firmware (ESP-IDF, Espressif IDE 3.1.0)

Develop in Espressif IDE with the ESP-IDF framework. Configure UART1 at 115200 / 8N1 and bind it to GPIO17/18 with uart_set_pin. Then read bytes and run the SIP-S parser.

SIP-S V1.0 frame (from the R60ABD1 manual §7 / EN §4.2):

Control classes: 0x01 heartbeat, 0x02 product info, 0x03 OTA, 0x05 work state, 0x07 range info, 0x80 presence, 0x81 breathing, 0x84 sleep, 0x85 heart rate.

Minimal ESP-IDF parse + dispatch:

#include "driver/uart.h"

#define RADAR_UART UART_NUM_1
#define TX_PIN     17
#define RX_PIN     18

void radar_init(void) {
    uart_config_t cfg = {
        .baud_rate = 115200,
        .data_bits = UART_DATA_8_BITS,
        .parity    = UART_PARITY_DISABLE,
        .stop_bits = UART_STOP_BITS_1,
        .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
    };
    uart_param_config(RADAR_UART, &cfg);
    uart_set_pin(RADAR_UART, TX_PIN, RX_PIN, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
    uart_driver_install(RADAR_UART, 256, 256, 0, NULL, 0);
}

// Returns true on a valid frame; fills ctrl/cmd/data/dlen.
static bool parse_frame(const uint8_t *b, int n, uint8_t *ctrl, uint8_t *cmd,
                        const uint8_t **data, int *dlen) {
    for (int i = 0; i + 9 <= n; i++) {
        if (b[i] != 0x53 || b[i+1] != 0x59) continue;
        *ctrl = b[i+2]; *cmd = b[i+3];
        int len = (b[i+4] << 8) | b[i+5];
        int data_end = i + 6 + len;
        if (data_end + 3 > n) return false;
        int sum = 0; for (int k = i; k < data_end; k++) sum += b[k];
        if ((sum & 0xFF) != b[data_end]) continue;
        if (b[data_end+1] != 0x54 || b[data_end+2] != 0x43) continue;
        *data = &b[i+6]; *dlen = len;
        return true;
    }
    return false;
}

Decoding the breathing and sleep frames

The R60ABD1 manual defines these report frames (manual v3.6, §7 command tables). After a valid frame, dispatch on ctrl/cmd:

Example: a breathing-rate frame is 53 59 81 02 00 01 [rate] [chk] 54 43. A sleep-state frame is 53 59 84 02 00 01 [state] [chk] 54 43. The manual's own test vector 53 59 80 81 00 01 0F BD 54 43 (checksum 0xBD) is a handy parser sanity check.

Optional: publish to MQTT

The ESP32 publishes — the module never does. Using the esp-mqtt component, post a broker-agnostic topic such as radar/R60ABD1/state with JSON like {"breath":22,"sleep":1}. Point it at your own Mosquitto/EMQX/broker; nothing here is tied to a vendor cloud. This is exactly the "add your own microcontroller" path the architecture article describes for modules that lack networking.

Notes and safety

• The module is not a medical device. Breathing/sleep values are indicators, not a diagnosis.
• Verify the 5 V budget before relying on the board's 5V pin; use a separate supply if needed (keep GND common).
• Keep GPIO19/20 clear — they are the native-USB debug path.
• Default ESP-IDF console stays on UART0; we left it alone, so logs and flashing keep working.

Where to go next

• Two architectures explained: MQTT vs UART
• The platform-agnostic parser: Minimal UART parser (SIP-S V1.0)
• First-good-frame checklist: Bring-Up checklist
• Module specs: 60 GHz / 24 GHz module spec sheet
• The GPIO angle: GPIO vs UART

Both the R60ABD1 module and the ESP32-S3 board are on Tindie.

Get the ESP32-S3-WROOM-1 dev board and the R60ABD1 radar module on Tindie, and build this UART-to-MQTT gateway today.