Introduction
While studying CompTIA Network+, I couldn't fully understand how Traceroute and Tracert work.
I could memorize them as the tool for tracing routes, but I couldn't comprehend how they work and what TTL is.
Once I grasped them through familiar example, everything clicked, so I decided to write it down.
What is Traceroute / Tracert
They are tools for investigating which route data takes to reach its destination.
The difference between Traceroute and Tracert
Traceroute → Command used in Linux・macOS
Tracert → Command used in Windows
They work the same way, but the name differs depending on the OS.
Why are they needed
Problem：
Cannot connect to network or delayed
Cannot identify where the problem is occurring
Solution：
Check each route data pass through
→ Identify the router that delay or lost happens
Familiar example
If a package sent from Tokyo to Osaka never arrives：
Check tracking number：
Warehouse in Tokyo → Center in Nagoya（The good is stopped at this facility）
→ Find that the center in Nagoya has problem
Similarly, with Traceroute：
PC → Router A → Router B（Delay happens）→ Destination
→ Find that Router B has problem
Practical output image
$ traceroute google.com
1 192.168.1.1 1ms 1ms 1ms ← Home Router
2 10.0.0.1 5ms 5ms 5ms ← ISP Router
3 172.16.0.1 10ms 10ms 10ms ← Intermediate Router
4 8.8.8.8 20ms 20ms 20ms ← Destination
How to check the output
Number（1・2・3）= Hop count（Passed Router number）
IP Address = The address of the Router
ms = Response time（3 times measuring）
* * * = No response（Timeout）
→ Settings that the Router do not response
→ Or any problem happens
What is TTL
TTL stands for Time To Live
In a nutshell, remaining number that packets can pass routes
Why TTL is needed
Problem：
If packets cannot reach their destinations and keep flowing in network
↓
Traffic congestion happens in network
↓
Harm for other communication
Solution：
Attach a limit to each packet
→ Discard the packet after it passes through a set number of routers
→ Avoid network congestion
How TTL works
Packets generate：
TTL = 128（In case of Windows）
TTL = 64（In case of Linux/mac）
↓
Each time a packet passes through a router, the TTL decreases by one
↓
When TTL reaches 0, the packet is discarded
↓
「Time Exceeded」message is sent to senders
Understanding with diagram
PC（Sent at TTL=3）
↓
Router A Passed
（TTL decreases from 3 to 2 ）
↓
Router B Passed
（TTL decreases from 2 to 1 ）
↓
Router C
（TTL decreases from 1 to 0 ）
→ The packet is discarded
→ Send 「Time Exceeded」message to PC
↓
Don't reach them to the destination
The mechanism Traceroute / Tracert use TTL
This is the core concept of this article
Step 1：TTL = 1
↓
TTL becomes 0 at Router A
↓
Router A sends「Time Exceeded」message
↓
1 hop identified : Router A（192.168.1.1）
Step 2：TTL = 2
↓
Pass Router A （TTL 2→1）
TTL becomes 0 at Router B
↓
Router B sends「Time Exceeded」message
↓
Find 2hop = Router B（10.0.0.1）
Step 3：TTL = 3
↓
Pass Router A・B
TTL becomes 0 at Router C
↓
Router C sends 「Time Exceeded」message
↓
Find 3hop = Router C（172.16.0.1）
Step 4：TTL = 4
↓
Arrive at destination
↓
「Arrived」message is sent
↓
Traceroute complete
Understanding with courier service
Imagine a rule applied to every package:
①The count decreases by one at each relay center
②When the count reaches 0, a status message is sent back
TTL = 1：Goods stop at the warehouse in Tokyo
→ Message「Arrived at warehouse at Tokyo」
TTL = 2：Tokyo → Nagoya
Goods stop at the relay center in Nagoya
→Message「Arrived at the relay center in Nagoya」
TTL = 3：Tokyo → Nagoya → Osaka
Goods stop at the relay center in Osaka
→Message「Arrived at the relay center in Osaka」
TTL = 4：Tokyo → Nagoya → Osaka → Destination
Goods arrive to the destination
→ Message「Delivery completed」
Which layer does Traceroute / Tracert operate on?
Layer 7 Application │
Layer 6 Presentation │
Layer 5 Session │ Not applicable for Traceroute
Layer 4 Transport │
─────────────────────────────
Layer 3 Network ← Traceroute works
─────────────────────────────
Layer 2 Data Link │
Layer 1 Physical │
The reason why Traceroute / Tracert work at Layer 3：
→ Tracking routes with IP address
→ TTL is included in IP header
Summary
Traceroute/Tracert ：Tool for investigating the route data pass through
The difference of OS：
Linux/mac → traceroute
Windows → tracert
TTL ：The remaining number of routers a packet can pass through
→ Decreases by 1 each time it passes through a router
→ 0 means the packet is discarded and send Time Exceeded message
Traceroute / Tracert use TTL：
Send data with TTL
→ Each router send「Time Exceeded」message, which can verify how many hop counted
→ Can comprehend routes overall
OSI refecence model：Layer 3（Network Layer）
Use case：
→ Not connect to network
→ Lag and delay with communication
→ Identify which router is causing the problem
Conclusion
I used to struggle with memorizing these tools over and over.
Once I understood the mechanism through a familiar example, everything naturally fell into the place.
TTL = Expiration time packets have（Remaining hop count router can pass ）
→ Count down by 1 as router pass
→ 0 means responding「Time Exceeded」message
Traceroute / Tracert = Tool for identifying where the issue occurs by increasing TTL number from 1
